Ortlinghaus. Clutches (2024)

Ortlinghaus. Clutches (7)


Hydraulic multi-plate clutch | Series 002

Hydraulic multi-plate clutch | Series 002

Based on our friction linings, which have been tried and trusted for many years in the marine sector, clutches in this series reconcile high torque and thermal absorption rates as well as a favorable outer diameter. A high shaft diameter can also be used.

Due to their broad power spectrum, smaller sizes can be achieved with corresponding weight and cost benefits, especially in higher torque ranges. The optimized outer diameter makes shorter distances between axles possible, and in this way offers clear savings potential in the gearbox.

The hydraulic multi-plate clutch impresses with its comprehensive service friendliness. The plate pack, which is wear-free under the specified conditions, can be accessed from either side depending on the model, and ensures an easy, safe, and swift replacement of the plate pack. The special design also ensures that other components cannot fall out during replacement.

The Ortlinghaus muti-plate clutches safely accelerate even large propellers and generators. This optimal further development of our tried-and-tested technology sets today's industry standards.

Torque:
150 - 1,600,000 Nm
Rotations per minute:
9,800 - 350 min-1
Outside diameter:
90 - 1,200 mm
Bore diameter:
35 - 500 mm
Length:
64 - 755 mm

Ortlinghaus. Clutches (9)

Electromagnetic clutch | Series 008

Electromagnetic clutch | Series 008

Magnetically actuated, rapid switching dry-running clutches and brakes for machines and many other devices. They permit space saving, adaptable to different design situations. When disengaged, these clutches and brakes are free of residual torque. They can be supplied either with magnet bodies in a mounted versionwith bearings or flange fixings to the machine frame.

Torque:
1.7 - 480 Nm
Outside diameter:
68 - 266.5 mm
Bore diameter:
15 - 80 mm
Length:
40 - 90 mm

Ortlinghaus. Clutches (11)

Electromagnetic tooth clutch | Series 013

Electromagnetic tooth clutch | Series 013

The model 013 series slip ring-free electromagnetic tooth clutch enables a very compact design due to form-fitting torque transmission.

Torque:
80 - 1,600 Nm
Outside diameter:
82 - 195 mm
Bore diameter:
25 - 65 mm
Length:
44 - 84 mm

Ortlinghaus. Clutches (13)

Hydraulical clutch | Series 021

Hydraulical clutch | Series 021

Based on our friction linings, which have been tried and trusted for many years in the marine sector, clutches in this series reconcile high torque and thermal absorption rates as well as a favorable outer diameter. A high shaft diameter can also be used.

Due to their broad power spectrum, smaller sizes can be achieved with corresponding weight and cost benefits, especially in higher torque ranges. The optimized outer diameter makes shorter distances between axles possible, and in this way offers clear savings potential in the gearbox.

The hydraulic multi-plate clutch impresses with its comprehensive service friendliness. The plate pack, which is wear-free under the specified conditions, can be accessed from either side depending on the model, and ensures an easy, safe, and swift replacement of the plate pack. The special design also ensures that other components cannot fall out during replacement.

The Ortlinghaus muti-plate clutches safely accelerate even large propellers and generators. This optimal further development of our tried-and-tested technology sets today's industry standards.

Torque:
150 - 1,600,000 Nm
Rotations per minute:
9,800 - 350 min-1
Outside diameter:
90 - 1,200 mm
Bore diameter:
35 - 500 mm
Length:
64 - 755 mm

Ortlinghaus. Clutches (15)

Main drive locking clutch | Series 055

Main drive locking clutch | Series 055

According to DIN EN ISO 16092, the relevant safety standards for press engineering, a mechanical restraining device must be present in mechanical presses for repair work and work between the two halves of the tool. The Ortlinghaus linear motion lock from the series 055 is an approved restraining device according to the German employers' liability insurance association. The linear motion lock is used to positively lock a shaft to the fixed housing of a clutch so that the shaft cannot rotate. This is particularly desirable for presses to ensure that the press ram will not move in an uncontrolled or unintended manner during servicing or maintenance work between the two halves of the die.

The Ortlinghaus ram locking mechanism enables a variable locking of the press ram in any position, with a short actuating time. The linear motion lock is matched to and integrated into the machine's drivetrain. It is engaged or disengaged hydraulically. The state of the ram locking mechanism actuated by oil pressure, either locked or unlocked, is detected using inductive travel sensors and transmitted to the machine control unit.

Torque:
11,000 - 100,000 Nm
Outside diameter:
480 - 900 mm
Bore diameter:
120 - 260 mm
Length:
195 - 325 mm

Ortlinghaus. Clutches (17)

Hydraulic clutch | Series 127

Hydraulic clutch | Series 127

Hydraulically actuated clutches and brakes work exclusively with “wet-running” oil-cooled plates with the friction pairing steel/sintered lining. The advantages of actuation with pressure oil at 80 bar, the multi-plate construction type and the oil-cooled friction pairing steel/high-performance sinter result in an exceptionally compact design with high performance. They feature high torques, low mass moments of inertia, high switch times and little maintenance. The separate design requires different shaft ends for installation, which makes it possible to use different clutch and brake sizes. Since they run in a sealed housing, no dirt is released into the environment.

The international safety regulations for press manufacture were taken into consideration for the design. The clutch-brake combinations have been recognized as safe by the German Employers’ Liability Insurance Association and type-tested by the Swedish Industrial Safety Authority.

Torque:
up to 300,000 Nm

Ortlinghaus. Clutches (19)

Hydraulical clutch | Series 202

Hydraulical clutch | Series 202

In its company‘s history of more than hundred years, Ortlinghaus has built an image as a strong partner for the marine industry concerning clutches, brakes and plates. Based on this experience Ortlinghaus developed the hydraulically actuated multiplate clutch series 202.

All construction details had been adapted to the marine industry and optimized. The result is a modern multi-plate clutch as consequent development of proven technology. A high torque with simultaneous high heat capacity is achieved, connected with low weight due to a smaller outside diameter. Additionally there is the possibility to use a large shaft diameter. Because of the power-density, it is possible, especially with torque ranging high, to choose a smaller unit size for less weight and cost. The smaller outside diameter allows smaller shaft centre distance for weight and cost savings of the transmission. Special attention during development was focus on easy maintenance. Thus the plate package – which works free of wear in the defined operational conditions – can be accessed from both sides depending on series-design. Thus other parts are prevented from falling-off during service work. Because the core clutch components are based on proven technology, this clutch will also provide the safety Ortlinghaus is known for. It will contribute to accelerate large propeller- and generator masses in a secure manner.

Torque:
22,000 - 1,600,000 Nm

Ortlinghaus. Clutches (21)

Slipping clutch | Series 600/700

Slipping clutch | Series 600/700

Ortlinghaus slipping clutches are always used when external peak loads need to be absorbed and smoothed safely. They provide protection from peak torque and unexpected stoppages. As the release torque can be set, torque is also transferred during slipping so that no uncontrolled torque transmission takes place. A reset is not required either.

Our safety clutches have proven their worth over decades of themost demanding mining use and they undergo constant furtherdevelopment.

Torque:
20 - 50,000 Nm
Outside diameter:
70 - 700 mm
Bore diameter:
12 - 250 mm
Length:
90 - 300mm

Ortlinghaus. Clutches (23)

Electromagnetic clutch | Series 893

Electromagnetic clutch | Series 893

These electromagnetic clutches are used to empty grain tanks. Standard products are used with minor modifications in this application.

Torque:
480 Nm
Rotations per minute:
440 min-1
Outside diameter:
340 mm
Bore diameter:
Custom designed
Length:
Custom designed

Ortlinghaus. Clutches (25)

Hydraulic PTO clutch | Series 992

Hydraulic PTO clutch | Series 992

PTO clutches are used in front and rear gearboxes for tractors and engage and disengage different kinds of machinery. Highly integrated solutions are necessary for the customer. Many solutions have been designed.

Torque:
500 - 4,000 Nm
Rotations per minute:
540 - 1,000 min-1
Outside diameter:
160 - 320 mm
Length:
Custom designed

Ortlinghaus. Clutches (27)
Ortlinghaus. Clutches (2024)
Top Articles
Latest Posts
Recommended Articles
Article information

Author: Duane Harber

Last Updated:

Views: 5567

Rating: 4 / 5 (51 voted)

Reviews: 90% of readers found this page helpful

Author information

Name: Duane Harber

Birthday: 1999-10-17

Address: Apt. 404 9899 Magnolia Roads, Port Royceville, ID 78186

Phone: +186911129794335

Job: Human Hospitality Planner

Hobby: Listening to music, Orienteering, Knapping, Dance, Mountain biking, Fishing, Pottery

Introduction: My name is Duane Harber, I am a modern, clever, handsome, fair, agreeable, inexpensive, beautiful person who loves writing and wants to share my knowledge and understanding with you.